Sold in 500 mL Bottles
Dry Boiling Point of 325°C
High Wet Boiling Point of 216°C
Specially Designed for Racing Applications

Description
Vehicle Fitment
Technical Data
Included
Install Guide

Motul RBF 600 Racing DOT 4 Brake Fluid - 500mL

If you've ever felt your brake pedal go soft mid-session, you already know what boiling brake fluid feels like. It's terrifying, and it's avoidable. Motul RBF 600 is a fully synthetic DOT 4 racing brake fluid with a 312°C (594°F) dry boiling point and a 216°C (421°F) wet boiling point - numbers that laugh at what stock brake fluid can handle. Regular DOT 4 fluid starts boiling around 230°C dry and 155°C wet. When you're hammering the same set of brakes lap after lap, that gap in boiling points is the difference between a confident brake pedal and a scary sponge.

Why Your Brake Fluid Boils Before Your Pads Give Up

Here's what's actually happening: your pads and rotors dump heat into your calipers, and your calipers cook the fluid sitting right next to the pistons. It doesn't take a full track day to get there - one aggressive session at a tight circuit with heavy braking zones can spike your caliper temps enough to boil stock fluid. Once it boils, you've got vapor in your lines, and vapor compresses. That's your pedal going to the floor. RBF 600's 312°C dry boiling point gives you a serious buffer before any of that happens.

The Wet Boiling Point Is the Number That Actually Matters

Brake fluid is hygroscopic - it absorbs moisture from the air constantly, even through your brake lines. That moisture drops the boiling point fast. A fresh bottle of budget racing fluid might advertise an impressive dry boiling point, but after a few months in your car, the wet boiling point is what you're actually relying on. RBF 600's 216°C wet boiling point is exceptionally high for a DOT 4 fluid, which means it stays stable even after it's been in your system a while. That said, don't get complacent - change it regularly.

Steel, Carbon, or Ceramic Brakes - RBF 600 Handles All of Them

Running a stock steel setup on a track-day Civic? RBF 600 works. Running carbon or ceramic brakes on a dedicated race car? Also works. Carbon and ceramic brake systems run significantly hotter than steel, so if you've upgraded your braking hardware, you absolutely need fluid that can keep up. RBF 600 is compatible with all hydraulic brake systems and meets FMVSS 116 DOT 4, SAE J 1703, and ISO 4925 standards - so it's not just a track-only solution, it's street legal too.

Change It After Every Event. No Exceptions.

Heat cycles break down the fluid's additives and lower its boiling point even when it never actually boils. If you're racing wheel-to-wheel, flush and replace after every event. If you're doing track days, change it every 2-3 events minimum. And don't just top off - flush the entire system. Mixing fresh fluid into old, heat-cycled fluid defeats the whole point. Brake fluid is cheap. Brake repairs - and the alternative - are not. One 500mL bottle is enough for a full system flush on most cars.

What's in the Box
- Motul RBF 600 racing brake fluid - 500mL bottle
- Fully synthetic DOT 4 formula
- 312°C (594°F) dry boiling point
- 216°C (421°F) wet boiling point
- Meets FMVSS 116 DOT 4 / SAE J 1703 / ISO 4925 standards
- Compatible with all hydraulic brake and clutch systems
- Works with steel, carbon, and ceramic brake systems
- Street legal
Storage and Use Notes: Keep unopened bottles in a cool, dry place. Once you crack the seal, use the whole bottle or toss what's left - an open bottle absorbs moisture fast and degrades quickly. Always flush your full brake system when changing fluid. Don't top off old fluid with new. Get all the heat-cycled fluid out of the system before adding fresh RBF 600.
Universal fit - compatible with all hydraulic brake and clutch systems. Works with steel, carbon, and ceramic brake rotors. DOT 4 compatible with any vehicle that uses DOT 3, DOT 4, or DOT 5.1 brake fluid (do not use with DOT 5 silicone-based systems).

Fluid Type	Fully Synthetic DOT 4
Dry Boiling Point	312°C (594°F)
Wet Boiling Point	216°C (421°F)
Volume	500 mL (16.9 fl oz)
Color	Clear to Light Yellow
Base	Glycol Ether / Borate Ester
Compliance Standards	FMVSS 116 DOT 4, SAE J 1703, ISO 4925
Compatible Systems	All hydraulic brake and clutch systems (DOT 3, DOT 4, DOT 5.1 compatible - NOT for use with DOT 5 silicone systems)
Compatible Brake Types	Steel, Carbon, Ceramic
Street Legal	Yes
Recommended Change Interval	After every race event; every 2-3 track days minimum; annually for street use

- (1) Motul RBF 600 Racing DOT 4 Brake Fluid - 500 mL bottle

Accord 1990-1993 Brakes